. HUAWEI Quidway S2000-EI Series Ethernet Switches Installation Manual VRP3.10. 3104A007 Huawei Technologies Co., Ltd. Provides customers with comprehensive technical support and service. If you purchase the products from the sales agent of Huawei Technologies Co., Ltd., please contact our sales agent. If you purchase the products from Huawei Technologies Co., Ltd. Directly, Please feel free to contact our local office, customer care center or company headquarters.
Dec 13, 2018 - Method 1: Obtain the Card Serial Number Using a Command. Run the display elabel command to view electronic label information, and select the slot ID according to the command prompt information. In the command output, BarCode specifies the serial number of a card. The command format may vary according to the version. 4-3 Using the Command Line Interface (CLI) Using the CLI Startup Config file in non-volatile memory. If you reboot the switch without first using write memory, all changes made since the last reboot or write memory (whichever is later) will be lost.
Trademarks, HUAWEI, C&C08, EAST8000, HONET. QoS/ACL, integrated management, STP, security and system management. Organization Quidway S2000-EI Series Ethernet Switches Installation Manual mainly introduces the hardware features, installation, configuration and maintenance of S2000 EI Series Ethernet Switches. To avoid any possible device damage and personal injury before the installation and during the installation, please read the manual carefully.
Chapter 4 Powering on Switch for the First Time The chapter introduces the booting process of S2000-EI Series Ethernet Switches, including the power-on booting of the switch and the system initialization. Chapter 5 BootROM and Host Software Loading The chapter introduces several means to upgrade the software of S2000-EI Series Ethernet Switches. GUI conventions Convention Description Button names are inside angle brackets. For example, click the button. Window names, menu items, data table and field names are inside square brackets.
For example, pop up the New User window. Multi-level menus are separated by forward slashes. Environmental Protection This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed. Installation Manual Quidway S2000-EI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 Product Overview.1-1 1.1 S2008-EI Ethernet Switch.1-1 1.1.1 Appearance.1-1 1.1.2 Front View.
1-1 1.1.3 Rear View. 1-4 1.2 S2016-EI Ethernet Switch.1-5 1.2.1 Appearance. Installation Manual Quidway S2000-EI Series Ethernet Switches Table of Contents 3.4.4 Connecting Ground Wire.3-7 3.5 Connection of Console Cable. 3-9 3.5.1 Console Cable.3-9 3.5.2 Connecting Console Cable. 3-10 3.6 Installation/Removal of Optional Interface Modules.3-11 3.6.1 Installing Optional Interface Module. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview Chapter 1 Product Overview 1.1 S2008-EI Ethernet Switch 1.1.1 Appearance Figure 1-1 S2008-EI Switch 1.1.2 Front View I. Front panel On S2008-EI front panel distribute one power LED (POWER), eight fixed.
Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview (3) (4) (3) (4) (1) POWER LED (2) Eight fixed electrical ports (3) Port LED (left) (4) Port LED (right) (5) A/L mode LED (6) D/S mode LED (7) MODE button Figure 1-2 S2008-EI front panel II. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview By toggling between the A/L and D/S mode LEDs using the MODE button, you can gather information about ACTIVE/LINK state and DUPLEX/SPEED using the port LEDs with reference to the following table. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview 1.1.3 Rear View I. Rear panel On the S2008-EI rear panel distribute external power input and Console port (see the following figure): (1) Power input (2) Console port Figure 1-3 S2008-EI rear panel. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview 1.2 S2016-EI Ethernet Switch The S2016-EI Switch falls into two models: S2016-EI-AC and S2016-EI-DC. They differ only in the sense that the former is AC-powered and the latter is DC-powered.
Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview (1) MODE button (2) D/S mode LED (3) A/L mode LED (4) PWR LED (5) 16 fixed electrical ports (6) Port LED (left) (7) Port LED (right) (8) Expansion slot. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview Table 1-6 Port LEDs on S2016-EI front panel Status Port LED status Description mode LED Flashing (faster for heavier traffic, and nearly steady Traffic is being received or transmitted ON when the traffic is on the port.
Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview Table 1-8 Console port attributes Attribute Description Connector RJ-45 Port standard Asynchronous EIA/TIA-232 Baud rate 9600 (default) Connection to the ASCII terminal Connection to the serial port of a local terminal (which can be a PC) or a. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview 1.3 S2403H-EI Ethernet Switch The S2403H-EI Switch falls into two models: S2403H-EI-AC and S2403H-EI-DC. They differ only in the sense that the former is AC-powered and the latter is DC-powered. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview II.
LEDs on S2403H-EI front panel You can gather information about the status of the S2403H-EI and the ports using the LEDs on its front panel. Power LED Table 1-9 Power LED on S2403H-EI front panel.
Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview Status Port LED status Description mode LED The port is in full duplex mode. Yellow (DUPLEX) The port is in half duplex mode. Flashing (at frequencies of mode The port operates at 100 Mbps. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview 1.3.3 Rear View I. S2403H-EI-AC rear panel (1) AC power socket (2) Grounding screw Figure 1-10 S2403H-EI-AC rear panel II. S2403H-EI-DC rear panel (1) DC power socket (2) Grounding screw Figure 1-11 S2403H-EI-DC rear panel 1.3.4 Optional Modules.
Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview Item S2000-EI Series Ethernet Switches S2008-EI: 8 Number of fixed S2016-EI: 16 Ethernet port S2403H-EI: 25 Console port One Console port S2008-EI: 0 Number S2016-EI: 1 expansion slots S2403H-EI: 1. Installation Manual Quidway S2000-EI Series Ethernet Switches Chapter 1 Product Overview Item S2000-EI Series Ethernet Switches S2008-EI uses external power supply. The input voltage and output voltage are as follows: Input rated voltage: 100 - 240 V a.c.; 50/60 Hz Input maximum tolerance: 90 - 264 V a.c.
Important note: after entering this 'question' I did some testing and realized I am able to enable the broadband connection with newer version of Ubuntu Server - 15.10. The procedure is described below. Anyway, the reason why it does not work in 14.04.04LTS is not known to me (maybe the functionality is not covered in its kernel version) I have Huawei E3372H which I set to 'modem' mode, so it does not do NAT and behaves as a modem. It works with Ubuntu 15.10 (desktop). Network manager shows possibility for creating a broadband connection and I just fill APN 'internet' and that's it - after enabling this connection it works perfectly. But how to connect my Ubuntu Server 14.04 on to the internet using this USB stick when there is no NetworkManager installed? Here is some basic info about the stick: lsusb shows it as: Bus 002 Device 009: ID 12d1:1506 Huawei Technologies Co., Ltd.
After further testing I found I had kernel version 3.16 on my Ubuntu Server 14.04.4. With this kernel version, Huawei E3372H did not work properly in cdcncm mode. The solution is to upgrade the kernel to 4.2. Then connection to the internet can be done with these simple commands (assuming the modem created /dev/ttyUSB0, APN is 'internet'): This command will connect the stick to LTE netowrk (internet is an APN, so other providers can use different APN name): echo -e 'AT^NDISDUP=1,1, 'internet ' r' /dev/ttyUSB0 This command will acquire IP address for the wwan0 interface: dhclient wwan0.